Disclaimer

General Disclaimer

The information provided by CutAndWeld (“https://www.cutandweld.com”) is for general informational and educational purposes only. All information on the site is provided in good faith; however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information on the site.

The use of any information or tools from this website is entirely at your own risk, for which we shall not be liable. It shall be your responsibility to ensure that any information or tools available through this website meet your specific requirements and circumstances.

Not Professional Engineering, Structural, or Safety-Certification Advice

All welding, cutting, and metal fabrication content on CutAndWeld is general educational material. It does NOT constitute professional engineering advice, structural design advice, or safety certification of any kind, and it is not a substitute for the training, codes, and qualified oversight that real fabrication work requires. Nothing on this site qualifies you to perform code work, and no article can assess your specific joint, material, equipment, or working conditions. Structural and load-bearing welds — anything whose failure could injure someone or damage property, such as trailers, railings, vehicle frames, lifting equipment, and building components — must be designed, performed, and inspected by certified professionals in accordance with the applicable codes and standards (such as those published by the American Welding Society) and local regulations.

Welding Safety

Welding and cutting are inherently hazardous activities. Arc welding involves lethal voltages and currents, extreme temperatures, intense ultraviolet and infrared radiation, flying sparks and molten metal, compressed and flammable gases, and toxic fumes. Before you strike an arc or light a torch, always:

• Wear proper PPE:Use an appropriate welding helmet with the correct shade lens, flame-resistant clothing, welding gloves, safety glasses, and suitable boots. Never look at an arc with unprotected eyes — even a brief exposure can cause arc eye (photokeratitis), and repeated exposure can cause permanent damage. Protect bystanders with screens.
• Control fumes and ventilation: Welding fumes are toxic; some, such as those from galvanized, stainless, or coated metals, are severely so. Work with adequate ventilation or fume extraction, use respiratory protection where required, and never weld on containers that have held flammable or unknown substances.
• Prevent fires: Clear flammable materials from the work area, keep a suitable fire extinguisher within reach, watch for smouldering material after the work is done, and follow hot-work procedures where they apply.
• Follow the manuals:Read and follow the manufacturer’s manuals and safety instructions for your specific welder, cutter, gas equipment, and consumables. Manuals override anything you read here.
• Comply with local codes and standards: Electrical supply, gas storage, hot work, and structural welding are regulated. Follow the codes and standards that apply where you live and work (including AWS and equivalent national standards), and obtain the permits and inspections your jurisdiction requires.
• Know your limits: Get hands-on instruction before attempting unfamiliar processes, and leave structural, pressure, and code work to certified professionals.

If you are ever unsure whether a weld, a setup, or a procedure is safe, stop and consult a qualified professional before proceeding.

Our Calculators Are General-Purpose Utilities

The calculators on CutAndWeld — the Age Calculator, GPA Calculator, Percentage Calculator, Unit Converter, Date Calculator, Countdown Timer, Tip Calculator, and Random Number Generator — are general-purpose everyday utilities. They are handy around the shop for things like converting measurements, working out percentages, and tracking dates, but they are NOT engineering tools. They do not calculate weld strength, joint design, filler selection, heat input, load capacity, or any other engineering value, and their output must never be used as the basis for structural or safety-critical decisions.

Calculation Accuracy

Our calculators provide results based on standard formulas and the figures you enter. Results should be used as starting points and planning aids, not absolute values or guaranteed outcomes. Mistyped inputs, rounding, and differing conventions can all affect results — double-check anything that matters.

Tool and Content Limitations

Real-world outcomes in welding and fabrication vary significantly due to:

• Materials: Alloy, thickness, coating, cleanliness, and prior heat treatment all change how a metal cuts and welds.
• Equipment: Machine type, condition, settings, consumables, and gas selection differ from shop to shop.
• Skill and Technique: Travel speed, angle, fit-up, and preparation are learned by practice and vary by operator.
• Environment: Wind, temperature, humidity, and workspace constraints affect both quality and safety.

Our Recommendations

For best results in the shop:

• Treat our guides as starting points, not step-by-step certification.
• Always follow your equipment manufacturer’s manuals and settings charts.
• Practice on scrap of the same material before welding the workpiece.
• Have structural or safety-critical work designed and inspected by certified professionals.
• Compare multiple trusted sources and keep learning.

Not Professional Advice

CutAndWeld tools and content do not constitute:

• Engineering or Structural Advice:Information about processes, joints, and materials is general only and is not a substitute for a qualified engineer’s assessment of your specific application.
• Safety Certification or Training: Our content is educational only and never replaces formal training, hot-work procedures, equipment manuals, or the safety standards that apply to your work.
• Guaranteed Outcomes: Guides and calculator outputs are aids only and are not a guarantee of weld quality, strength, fitness for purpose, or results.
• Certified Expertise: Our content supplements but does not replace certified welders, inspectors, and engineers.

Consult a certified professional for:

• Structural, load-bearing, or safety-critical welds of any kind
• Pressure vessels, gas systems, and anything covered by a code
• Vehicle frames, trailers, lifting gear, railings, and building components
• Weld inspection, testing, and certification requirements
• Electrical supply and installation for welding equipment
• Any job where you are unsure of the safe or compliant approach

No Warranty

CutAndWeld expressly disclaims all warranties, whether express, implied, statutory, or otherwise, including but not limited to implied warranties of merchantability, fitness for a particular purpose, and non-infringement. We do not warrant that our tools, calculations, or information are error-free, accurate, or complete, or that our website will be available without interruption at all times.

Limitation of Liability

To the maximum extent permitted by applicable law, in no event shall CutAndWeld be liable for any direct, indirect, punitive, incidental, special, consequential, or exemplary damages, including without limitation damages for personal injury, property damage, failed or defective work, lost materials, goodwill, use, or data arising out of or related to your use of our tools, content, and services.

User Responsibility

By using CutAndWeld tools and services, you acknowledge and agree that:

• You will use your own judgment, and consult a qualified professional, when applying anything you read here to your specific project and circumstances.
• You will follow your equipment manufacturer’s manuals, wear proper PPE, and comply with the codes, standards, and regulations that apply to your work.
• You are responsible for having structural, pressure, or safety-critical work performed and inspected by certified professionals.
• You assume all risks associated with welding, cutting, grinding, and metal fabrication, and with the use of our tools and information.

External Links Disclaimer

The site may contain links to other websites or content originating from third parties. Such external links are not investigated, monitored, or checked for accuracy, adequacy, validity, reliability, availability, or completeness by us. We do not warrant, endorse, guarantee, or assume responsibility for the accuracy or reliability of any information offered by third-party websites linked through the site.

Advertising Disclaimer

CutAndWeld displays advertisements from third-party advertising networks, including Google AdSense. These advertisements are clearly distinguishable from our editorial content. The presence of advertisements on our website does not constitute an endorsement of the advertised products or services.

Changes to This Disclaimer

We reserve the right to modify this disclaimer at any time. Changes will be posted on this page with an updated revision date. Your continued use of our website and tools after any changes indicates your acceptance of the modified disclaimer.

Contact Us

If you have any questions or concerns about this Disclaimer, please visit our Contact page or email us at admin@cutandweld.com.